ZY6288隔熱隔音材料耐燒穿試驗機
Insulation materials resistant to wear testing machine
一、型號：ZY6288Model: ZY6288
二、符合標準:Conform to the standard:
GB/T25352-2010
美國聯邦航空條例FAR25
民航局運輸類飛機標準CCAR-25-R4
GB/T25352-2010
The federal aviation regulations FAR25
The civil aviation administration of China transportation aircraft standard CCAR - 25 to R4
三、適用范圍:Scope of application:
本標準規定了隔熱隔音材料在高強度開放式火焰下的耐燒穿特性的試驗方法。
本標準適用于評估隔熱隔音材料在高強度開放式火焰下的耐燒穿特性。
This standard stimulates the insulation materials under high strength open flame resistant to burn through the
characteristics of the test method.
This standard applies to the evaluation of insulation materials under high strength open flame burn through
resistance properties.
四、主要性能參數：The main performance parameters:
1、試驗室：試驗室的地面長度與寬度均不應小于3.05m。
2、燃油導軌可調整，使燃油噴嘴位于距離出口固定片前端8mm的位置。出口固定片應安裝在通風管的端部。
3、燃油：燃油宜為JP-8、Jet A或上等效的燃油。其流量應為（0.378 0±0.012 6）L/min。如果不能獲得該燃油，4、當
燃油標稱流量、溫度和熱流量值符合標準要求時，可采用3號噴氣燃料或其他等效的燃油。
5、校準熱流計（可共用背面熱流計），為總熱流密度型、箔式Gardon熱流計，量程應為（0～22.7）W/m2，精度為指示讀數的
±3%。
6、校準熱電偶直徑為3.2mm的陶瓷包封、金屬護套、接地式K型（鎳鉻-鎳鋁）熱電偶，其金屬絲直徑應為0.511mm
7、記錄燒穿時間，即火焰穿透試樣的時間（如果有）或熱流超過2.27W／cm2的時間。
8、設備具有下列安全保護裝置：電源超載、 短路保護、控制回路過載保護。
9、采用16位板卡+微機控制，具有結構合理、性能穩定、操作簡便等優點；
10、測試期間實時顯示測量結果動態地繪出曲線，數據可以保存、調閱和打印輸出,可直接打印報表；
1, the laboratory: the laboratory floor length and the width should not be less than 3.05 m.
2, fuel rail can be adjusted, making the fuel nozzle export fixed at the front position of 8 mm. Export stator
should be installed in the ventilation pipe end.
3, fuel oil, fuel oil appropriate for JP - 8, the Jet fuel A or international equivalent. The flow rate shall
be the (0.378 0 + / - 0.012 6) L/min. If you can't get the fuel, 4, when the nominal fuel flow rate,
temperature and heat flow values conform to the requirements of the standards, can use 3 # jet fuel or other
equivalent fuel.
(5, calibration of heat flow meter can be Shared on the back of the heat flow meter), for the total heat flux
density, foil type Gardon heat flux meter, the range should be (0 ~ 22.7 W/m2), plus or minus 3% accuracy for
the indicator reading.
6, calibrating thermocouple diameter of 3.2 mm ceramic coating, metal sheath, grounding type K type
thermocouple (nickel chrome - nickel aluminum), the wire should be 0.511 mm in diameter
7, record burn through time, namely the flame through the sample time (if any) or heat flow more than 2.27
W/cm2.
8, the equipment has the following safety protection device: power overload, short circuit protection, control
circuit overload protection.
9, 16 + microcomputer control, high precision interface card has advantages of reasonable structure, stable
performance, easy operation;
10, during testing real-time display measurement results dynamically draw perfect curve, data can be stored
permanently and read and print output, can be directly printed statement;
本頁產品地址：http://m.521uz.com/sell/show-4361670.html
免責聲明：以上所展示的[ZY6288 隔熱隔音材料耐燒穿試驗機]信息由會員[東莞中諾臺灣質檢儀器設備有限公司]自行提供，內容的真實性、準確性和合法性由發布會員負責。
